怎樣有效率的批量清洗五金件呢？人工清洗是費時又費力的，現在用工成本又高，所以，五金件清洗日漸由超聲波清洗機來完成，尤其是數量較多，結構復雜時。下面來講講超聲波清洗機清洗五金件的技巧。

How to efficiently clean hardware in batches? Manual cleaning is time-consuming and laborious, and now the labor cost is high. Therefore, hardware cleaning is increasingly completed by ultrasonic cleaning machines, especially when the number is large and the structure is complex. Let's talk about the skills of cleaning hardware with ultrasonic cleaning machine.

超聲波清洗機的優勢在于其清洗方式是將五金件浸沒在清洗槽內液體中，利用超聲波的高頻率，通過換能器轉化為高頻動能，然后作用于清洗槽中的液體介質，使液體產生空化作用，不斷的形成無數個細微氣泡，并迅速爆裂，產生沖擊力沖擊物件表面，使表面污垢脫離，從而達到清洗的效果。

The advantage of ultrasonic cleaning machine is that its cleaning method is to immerse the hardware in the liquid in the cleaning tank, use the high frequency of ultrasonic wave, convert it into high-frequency kinetic energy through the transducer, and then act on the liquid medium in the cleaning tank, causing the liquid to produce cavitation, constantly forming countless fine bubbles, and rapidly bursting, generating impact force to impact the surface of the object, so that the dirt on the surface is separated, so as to achieve the cleaning effect.

這樣一來，只要是水能接觸到的部位都能清洗干凈，不留死角。并且同時作用于五金件的各個部位，不像人工那樣一點點的清洗，因此，效率高。

In this way, as long as the parts that can be touched by water can be cleaned, leaving no dead corners. It also acts on all parts of hardware at the same time, unlike manual cleaning, so it has high efficiency.

使用超聲波清洗設備為五金件除蠟、除塵時，可以用普通水加一些洗衣粉清洗即可，如果是除油，建議添加些除油的清洗劑，大批量清洗時可以給超聲波清洗機定制加裝濾油器，這樣水可以循環使用，不用頻繁換水。

When using ultrasonic cleaning equipment to remove wax and dust for hardware, you can use ordinary water and some washing powder for cleaning. If it is oil removal, it is recommended to add some degreasing cleaning agents. When cleaning in large quantities, you can customize and add oil filters to the ultrasonic cleaning machine, so that the water can be recycled without frequent water change.

而除銹則有專門的除銹劑。對于五金件上的碎屑，如果是盲孔可能效果不太好，因?yàn)槌暡ㄇ逑粗饕菍⒈砻娴奈酃该撾x，但沒辦法掉。較短的通孔則完全沒有問題，可以將孔里面的碎屑掉。

There is a special rust remover for rust removal. For the removal of debris on hardware, if it is a blind hole, the effect may not be very good, because ultrasonic cleaning is mainly to separate the dirt on the surface, but there is no way to remove it. There is no problem with the shorter through hole, and the debris in the hole can be removed.

關于五金超聲波清洗機的頻率，一般來說40KHz是通用頻率，可以勝任五金際件清洗工作，這在眾多客戶的實使用中也得到證實。但有些較復雜的精密的五金件可以考慮更高頻率，如80KHz，而有些五金件則相反，需要28KHz，這主要是針對除銹或者碎屑較多的情況。更多相關內容就來網站cmicroentropy.com咨詢吧。

As for the frequency of hardware ultrasonic cleaning machine, generally speaking, 40KHz is the general frequency, which can be competent for the cleaning of hardware parts, which has also been confirmed in the actual use of many customers. However, some complex and precise hardware can consider higher frequency, such as 80kHz, while some hardware, on the contrary, need 28kHz, which is mainly aimed at the situation of rust removal or more debris. For more information, please visit cmicroentropy.com.