通過式清洗機使用時存在異常的表現是怎樣的你知道嗎？實際上多個方面都能體現出來，要趕緊才行、下面小編為您解釋。

Do you know what the abnormal performance of the through type cleaner is? In fact, there are many aspects that can be reflected, and we need to solve them quickly. The following section explains for you.

在運行通過式清洗機的時候如果發現清洗的毛刷跳動或者發出異常的聲音，那么這個時候可以去檢查一下鏈條，一般出現這樣情況的原因是鏈條松動了，或者是軸承損壞的原因?？梢愿鼡Q軸承和對鏈條進行張緊加固。

If it is found that the cleaning brush jumps or makes abnormal noise when running the through type cleaner, you can check the chain at this time. Generally, the reason for this is that the chain is loose or the bearing is damaged. The bearing can be replaced and the chain can be tensioned and reinforced.

傳動軸轉速忽快忽慢不穩定，發生的原因可能是調速表出現問題或者鏈條松了?？梢哉覍?zhuān)門的技術人員來進行檢查。

The speed of the transmission shaft is unstable, which may be caused by a problem with the speed regulator or a loose chain. You can find special technicians to check.

在加工清洗的玻璃發生偏移，這樣的情況是壓輥兩頭受力不夠均勻了；的方式是及時的調整壓輥平衡。

When the glass being processed and cleaned is shifted, the force on both ends of the pressure roller is not uniform enough; The solution is to adjust the pressure roll balance in time.

在加工中玻璃出現破碎的現象，這個時候要注意了一定要及時修正后再使用，一般發生的原因是毛刷的軸承破壞了，還有壓輥壓不住玻璃，需要及時調整和更換。

The glass is broken during processing. At this time, it must be corrected in time before use. Generally, the reason is that the brush bearing is damaged, and the glass cannot be pressed by the pressing roller. It needs to be adjusted and replaced in time.

清洗后的玻璃還是不干凈，那么可能是噴水管壞了或者是堵了，毛刷的間距太大也會洗不干凈。要及時清理和調整間距。

The glass after cleaning is still not clean, so it may be that the water spray pipe is broken or blocked, and the spacing between brushes is too large, which also makes it difficult to clean. Clean and adjust the spacing in time.

一但通過式清洗機使用時存在異常的表現，您就要及時找原因及時處理好，防止問題程度變大，更多相關內容就來關注我們cmicroentropy.com了解吧！

Once there is abnormal performance in the use of the pass through washer, you should find out the reason in time and deal with it in a timely manner to prevent the problem from getting worse. Follow us at cmicroentropy.com for more information!